Astaxanthin Manufacturer: Softgels, Beadlets and Capsules from Haematococcus pluvialis

We are a contract manufacturer in Guangzhou producing natural astaxanthin from Haematococcus pluvialis. We handle esterified oleoresin in softgels, stabilised powder in hard capsules, and beadlets for gummies and stick packs. Potency is assayed by HPLC, and we check your dose against the EU novel food limit before locking a formula.

23 years
contract manufacturing experience
1,000–2,000
softgel pilot MOQ
4–6 weeks
lead time after approval
Astaxanthin Manufacturer: Softgels, Beadlets and Capsules from Haematococcus pluvialis

Why astaxanthin projects fail on potency and colour

Astaxanthin is a carotenoid that is sensitive to light, heat and oxygen. Two problems account for most failed astaxanthin projects. The first is potency: the label claims a milligram amount per capsule, but the raw material is an oleoresin with a stated percentage of astaxanthin, and the assay is by HPLC. If the oleoresin percentage and the fill weight are not reconciled, the finished capsule will not match the claim. The second is colour bleed: astaxanthin is a strong red pigment, and if the carrier is wrong it will migrate into a gummy matrix or through a two-piece capsule seam. Both problems are solved at the formula stage, not at the label stage.

Natural astaxanthin from Haematococcus pluvialis is normally esterified and carried in an oil. That affects stability and how it is dosed. Synthetic or fermentation-derived material behaves differently and is not a like-for-like swap. As an astaxanthin manufacturer, we start by confirming the source, the oleoresin percentage and the intended dosage form. Softgels are the default because the oleoresin sits in an oil carrier inside a sealed shell. Powders and gummies need beadlets, which encapsulate the pigment and reduce colour migration. The daily dose must be checked against the EU novel food limit for food supplements rather than copied from a US label.

What we control as your astaxanthin manufacturer

Natural source, verified
We work with Haematococcus pluvialis oleoresin, which is normally esterified and oil-carried. The certificate of analysis states the astaxanthin content as a percentage of the oleoresin, assayed by HPLC. We do not treat synthetic or fermentation-derived material as a substitute without a new formula and a new stability check.
Softgel as the default
Oleoresin in oil inside a softgel is the default form for astaxanthin. The sealed shell limits oxygen contact, and the oil carrier keeps the pigment dispersed. We make softgels in-house, with pilot runs from 500 bottles so you can test stability and colour before committing to a larger batch.
Beadlets for powders and gummies
For gummies and powder blends, raw oleoresin will bleed colour into the matrix. Beadlets encapsulate the astaxanthin, which reduces migration and protects it from heat during gummy drying. We specify beadlet grade and carrier so the colour stays where it should in the finished piece.
Hard capsules with stabilised powder
Where a softgel is not wanted, we fill hard capsules with a stabilised astaxanthin powder. The powder grade and the capsule shell must be matched, because a two-piece capsule seam is a path for colour migration if the carrier is wrong. We test seam integrity as part of the pilot.
Dose checked against EU limit
Astaxanthin is authorised as a novel food in the EU for food supplements with a stated daily limit. That limit is market-dependent and may change, so we verify the current figure for your destination market before locking a dose. We do not copy a US label dose into an EU formula.
Documents per batch
Each batch ships with a certificate of analysis stating astaxanthin content by HPLC. Export documents include certificate of origin, health certificate and MSDS where relevant. Our GMP certificate is from Intertek, and our ISO 9001:2015, ISO 22000:2018 and HACCP certificates are from CQC.

Operational specifications

SpecDetailNotes
MOQ by formSoftgels: 1,000 pieces for a pilot. Hard capsules, tablets, powder: from 500 units. Gummies and stick packs: higher first runs.Pilot runs are for stability and colour checks before scale-up.
Lead time4–6 weeks for a pilot run after formula and artwork approval. Sampling: 7–10 days.Lead time starts after approval, not at enquiry.
DocumentsCoA per batch with astaxanthin content by HPLC; certificate of origin; health certificate; MSDS where relevant.CoA states oleoresin percentage and mg per capsule.
PackingPowder in jars, sachets or stick packs; softgels and capsules in bottles or blisters; gummies in jars.Packaging sourcing available.
TestingHPLC assay for astaxanthin content; stability checks for light, heat and oxygen sensitivity; colour migration check in gummies and capsule seams.Test methods are stated on the CoA.

How an astaxanthin order runs

01
Source and form review
We confirm Haematococcus pluvialis oleoresin percentage, dosage form and target mg per capsule. Softgel, beadlet or stabilised powder is chosen here.
02
Dose and regulatory check
We check the daily dose against the EU novel food limit for food supplements for your destination market. The limit is verified at the time of the project.
03
Pilot batch
A pilot run from 1,000 softgels or from 1,000 units for other forms. Sampling takes 7–10 days; the pilot checks assay and colour migration.
04
Artwork and packaging
Label and packaging sourcing is handled in-house. Artwork approval is the trigger for the 4–6 week lead time on the pilot run.
05
Batch release and export
Each batch ships with a CoA, certificate of origin and health certificate. MSDS is provided where relevant. Markets served include the US, UK, EU, Canada, Australia, the Middle East and Southeast Asia.

Quality and certificates

Astaxanthin is assayed by HPLC, and the certificate of analysis states the astaxanthin content of the oleoresin as a percentage and the mg per capsule in the finished form. Because the material is sensitive to light, heat and oxygen, we run stability and colour-migration checks during the pilot: gummy matrix bleed and two-piece capsule seam migration are both tested before scale-up. Our factory holds GMP (Intertek), ISO 9001:2015 (CQC), ISO 22000:2018 (CQC), HACCP (CQC) and an NSF audit. Halal certification is line- and product-specific, so gelatin gummies and capsules are scoped separately. FDA facility registration is verified through our US agent Registrar Corp; this is registration, not FDA approval, and dietary supplements have no pre-market approval in the US.

GMP (Intertek)ISO 22000:2018HACCPISO 9001:2015Halal (line-specific)FDA facility registration

Astaxanthin manufacturing: from the algae to the softgel

Astaxanthin is one of the few ingredients where the label on the drum tells you almost nothing about what is inside it. Two suppliers can both sell "2% astaxanthin from Haematococcus pluvialis" and deliver materials that behave completely differently in a softgel line: different ester profiles, different carrier oils, different oxidation levels, different particle size. For a brand owner, that difference shows up 12 months later as colour drift, potency loss, or a failed stability study. This page covers what the raw material actually is, where the failure points are, and what to specify before you approve a batch.

Where the material actually comes from

Commercial astaxanthin for supplements has three sources. The dominant one is the microalga Haematococcus pluvialis, cultivated in closed photobioreactors or open ponds under nitrogen starvation, which triggers the alga to accumulate astaxanthin as a stress response. The second is the yeast Xanthophyllomyces dendrorhous (formerly Phaffia rhodozyma), used mostly in feed. Synthetic astaxanthin exists but is not permitted for human supplement use in the EU and is not what you want in a retail product.

The form in which the alga is harvested matters more than most buyers realise. In H. pluvialis the pigment is stored predominantly as mono- and di-esters of astaxanthin with fatty acids, plus a smaller free-form fraction, all inside a thick sporopollenin cell wall. That wall is difficult to digest and is the reason unbroken algal biomass has poor bioavailability. Suppliers therefore supply either cracked and dried biomass (typically 1.5–3% astaxanthin), an oleoresin extracted with supercritical CO2 or solvent (5–10%), or a microencapsulated beadlet (1–5%) designed for aqueous systems.

  • Oleoresin: highest concentration, oil-soluble, needs an antioxidant system and cold-chain discipline
  • Beadlet / microencapsulated powder: water-dispersible, better for stick packs and gummies, higher cost per milligram
  • Dried cracked biomass: cheapest per kilogram, lowest potency, gritty mouthfeel, hardest to hide in a capsule
  • Esterified vs free-form: esterified material is more stable in the matrix but needs saponification before assay, so stated percentages are not directly comparable between suppliers

The assay problem: esterified, free-form, and what the CoA means

Most astaxanthin methods on a certificate of analysis are HPLC with UV detection at 470–480 nm, after saponification to convert esters to free astaxanthin. If a supplier reports the result without telling you whether the sample was saponified, the number is not comparable to another supplier's number. A 5% oleoresin measured as free astaxanthin equivalent and a 5% oleoresin measured as total carotenoid esters can differ by 20–30% in real delivered potency.

There is a second layer: isomer composition. Natural astaxanthin from H. pluvialis is predominantly the 3S,3'S isomer, whereas synthetic material is a mixture. If a supplier is blending natural and synthetic material, or blending algal biomass with oleoresin, the isomer ratio and the carbon-14 natural-content test are the only reliable way to find out.

For a commercial specification we recommend fixing four numbers rather than one: total astaxanthin by HPLC after saponification, free-form fraction, esterified fraction, and moisture. Add a peroxide value and an anisidine value if the material is an oil, because oxidised oleoresin still passes an astaxanthin assay while smelling and performing like a different ingredient.

Stability is the real formulation problem

Astaxanthin is a polyene. It is oxidised by air, degraded by light, and isomerises under heat. In a softgel the pigment sits in a lipid matrix, which protects it from moisture but exposes it to dissolved oxygen and to any peroxides already present in the carrier oil. That is why the carrier oil specification matters as much as the astaxanthin specification: a refined oil with a low peroxide value will keep the pigment intact far longer than an inexpensive oil that is already slightly oxidised.

In powders and gummies the failure mode is different. Water activity above roughly 0.5, plus light and headspace oxygen, drives rapid fading. A gummy that starts as a deep orange-red can be visibly lighter within three months on a retail shelf. The practical answers are microencapsulation with a protective wall material, a light-blocking packaging format, and a modest overage backed by real stability data rather than a rule of thumb.

We run accelerated stability at 40 °C / 75% RH for 3 and 6 months plus real-time data at 25 °C / 60% RH, and we report astaxanthin retention as a percentage of the initial value at each timepoint. If a project has a 24-month shelf-life target, we will not sign off on the label claim without at least six months of real-time data.

Which dosage forms work, and which do not

Softgels are the natural home for astaxanthin: the fill can be an oleoresin dissolved in MCT or a refined vegetable oil, with tocopherols as a secondary antioxidant, and the gelatin or HPMC shell provides an oxygen barrier. Typical retail potencies are 4 mg and 12 mg; the technical limit is usually the fill volume and the mouthfeel of the oil rather than solubility.

Two-piece hard capsules can carry beadlets or oleoresin absorbed onto a carrier, and they are cheaper, but they offer less protection and powder blends tend to segregate during filling. Tablets are the weakest option: compression generates heat and shear, the pigment stains tooling, and the resulting tablet is usually larger than consumers want for a 12 mg dose.

Gummies are popular with brands and difficult with astaxanthin. The pigment is oil-soluble, so it must be emulsified into the gel, and the emulsion has to survive cooking and depositing. Colour is a real problem: astaxanthin at a dose that supports a claim will colour the gummy strongly, so any flavour or colour system has to be built around it rather than added afterwards. We usually recommend a beadlet with a stated emulsion stability rather than free oleoresin for this format.

What to put in the specification, and what to ask a supplier

A workable astaxanthin specification covers identity (source organism, natural content by C14 if claimed), assay method and basis, ester profile, moisture, peroxide and anisidine value for oils, heavy metals (lead, arsenic, cadmium, mercury), solvent residues where an extracted oleoresin is used, microbiological limits, and a stability data package. If the brand makes an organic or non-GMO claim, the cultivation and extraction documentation has to come with the lot, not afterwards.

We also ask every raw material supplier for the last three commercial lots of the same grade, not a special sample, because astaxanthin is a fermented ingredient and lot-to-lot variation in colour and potency is normal. Reviewing three lots tells you the real specification range. Then we run an identity and assay check in-house on receipt, and we keep the retention samples for the life of the finished batch.

On claims: astaxanthin has an authorised health claim in neither the EU nor the US. Structure/function wording such as "supports skin health" is used in the US with the appropriate disclaimer, while in the EU the ingredient is sold without a health claim at all. That constrains the label, not the formulation, but it should be settled before artwork is approved.

Questions brand owners ask

Is your astaxanthin natural or synthetic?+
We use natural astaxanthin from Haematococcus pluvialis, which is normally esterified and carried in an oil. Synthetic or fermentation-derived material is a different input and would require a new formula and stability check. The certificate of analysis states the source and the astaxanthin content by HPLC.
What is the MOQ for astaxanthin softgels?+
Softgels can start at 1,000 pieces for a pilot. Most other forms start from 1,000 units, and gummies and stick packs need higher first runs. The pilot is used to check assay and colour migration before a larger batch.
How do you stop colour bleed in gummies?+
Raw oleoresin will bleed into a gummy matrix. We use beadlets, which encapsulate the pigment and reduce migration during gummy drying. The beadlet grade and carrier are specified at formula stage, and colour migration is checked in the pilot batch.
What daily dose can I use in the EU?+
Astaxanthin is authorised as a novel food in the EU for food supplements with a stated daily limit. The limit is market-dependent and may change, so we verify the current figure for your destination market before locking a dose. We do not copy a US label dose into an EU formula.
Can you supply astaxanthin powder bulk?+
Yes. We supply stabilised astaxanthin powder for hard capsules and beadlets for powders and gummies. Bulk powder is packed in jars, sachets or stick packs. The certificate of analysis states the astaxanthin content by HPLC for each batch.
What certificates come with an astaxanthin order?+
Each batch ships with a certificate of analysis. Export documents include certificate of origin, health certificate and MSDS where relevant. Our factory holds GMP (Intertek), ISO 9001:2015, ISO 22000:2018 and HACCP (CQC), plus an NSF audit. Halal is line- and product-specific.

Start with a pilot batch

Send your target mg per capsule, dosage form and destination market. We will confirm the oleoresin percentage, check the EU novel food limit for your market, and quote a pilot run from 1,000 softgels or 1,000 units for other forms.

Related pages