Hyaluronic Acid Manufacturer for Oral Supplements: Fermentation-Grade Sodium Hyaluronate

We are a contract manufacturer of oral hyaluronic acid supplements, using sodium hyaluronate from microbial fermentation in molecular weight grades from tens of kDa to over one million Da. Hard capsules, stick packs, tablets and drinks made in-house in Guangzhou. MOQ from 1,000 units. EU novel food status checked per market before formula lock.

23 years
Contract manufacturing experience
500 units
MOQ for most dosage forms
4–6 weeks
Pilot run lead time after approval
Hyaluronic Acid Manufacturer for Oral Supplements: Fermentation-Grade Sodium Hyaluronate

What you are actually buying when you source hyaluronic acid

Most hyaluronic acid on the supplement market today is sodium hyaluronate produced by microbial fermentation, not extracted from rooster combs. The fermentation route gives a consistent molecular weight distribution and avoids the animal-derived supply chain that older cosmetic-grade material relied on. The molecular weight grade matters more than most buyers expect: low grades around tens of kDa behave differently in a capsule or stick pack than high grades over one million Da, changing viscosity, mouthfeel and how the powder flows on the filling line. We supply the material in the grade you specify and confirm it on the CoA per batch.

Hyaluronic acid is hygroscopic. It picks up water from the air, which shows up as clumping in powder blends and as softening in capsules over time. That is a process problem, not an ingredient problem, and it is controlled by low-humidity packing and desiccant sachets where the format allows. For oral use, the EU novel food status and permitted dose must be verified for the destination market before you lock a formula; we do not treat that status as permanent. Typical formulas combine hyaluronic acid with collagen, vitamin C or elastin, and each combination changes fill weight and flow properties.

What we control in a hyaluronic acid project

Fermentation origin
Sodium hyaluronate from microbial fermentation, not animal tissue. We confirm the source on the CoA and keep the documentation trail from material lot to finished batch, which matters when your market asks for the origin story in writing.
Molecular weight grades
Grades from around tens of kDa to over one million Da. The grade changes viscosity, mouthfeel and capsule behaviour. Tell us the grade on your spec sheet and we will confirm what the material does in your chosen dosage form before you commit to a pilot.
Hygroscopicity controls
Low-humidity packing and desiccant sachets are standard process controls for this material. We plan the fill room humidity and the pack format around the clumping risk, because a powder blend that clumps on the line becomes a fill-weight problem.
Capsules and stick packs
Hard capsules and powder stick packs are the most common formats for oral hyaluronic acid. Tablets need a binder to handle the material's flow, and drinks need a grade that disperses. We make all four in-house, so the format decision is not outsourced.
Combination formulas
Collagen, vitamin C and elastin are the usual partners. Each addition changes fill weight and flow properties, so we re-check the fill weight and the flow on the pilot batch rather than assuming the base formula carries over.
EU novel food check
Oral hyaluronic acid is a food supplement application, and the EU novel food status and permitted dose need checking per market before formula lock. We flag this at the specification stage so the regulatory question is settled before artwork.

Operational details

SpecDetailNotes
MOQ by formHard capsules: from 1,000 units. Powder stick packs: higher first run. Tablets: from 1,000 units.Softgels can start at 1,000 pieces for a pilot; gummies and stick packs need higher first runs.
Lead time4–6 weeks for a pilot run after formula and artwork approval. Sampling: 7–10 days.Lead time starts after approval, not at enquiry.
DocumentsCoA per batch; certificate of origin, health certificate, MSDS where relevant.Export documents issued for the destination market on request.
PackingLow-humidity packing; desiccant sachets where the format allows.Hygroscopic material: pack format is chosen around moisture control.
TestingMaterial grade and identity confirmed on the CoA per batch.We do not invent test methods or limits beyond what the CoA states.

How a hyaluronic acid project runs

01
Specification review
You send the target grade, dosage form and destination market. We check the molecular weight grade, the EU novel food status for that market, and the format fit before quoting.
02
Formula and pilot
Formula development covers the combination ingredients (collagen, vitamin C, elastin) and the fill weight. A small-batch pilot confirms flow and fill weight on the line.
03
Artwork and packing
Label and packaging sourcing runs alongside. Pack format is chosen for moisture control: low-humidity packing and desiccant sachets where the format allows.
04
Production
Hard capsules, stick packs, tablets or drinks are made in-house. CoA per batch is issued, and export documents are prepared for the destination market.
05
Release and export
Batch release follows the CoA. Certificate of origin, health certificate and MSDS where relevant are issued for the shipment.

Quality and certificates

The factory holds GMP (Intertek), ISO 9001:2015 (CQC), ISO 22000:2018 (CQC), HACCP (CQC), an NSF audit, Halal certification from the Halal Foundation Center that is line- and product-specific, and FDA facility registration verified through the US agent Registrar Corp. FDA registration is not FDA approval; dietary supplements have no pre-market approval in the US. Halal scope is line- and product-specific, so gelatin gummies differ from capsules and the scope is confirmed per product. We do not claim any certificate for this ingredient beyond the scope the factory holds.

GMP (Intertek)ISO 22000:2018HACCPISO 9001:2015Halal (line-specific)FDA facility registration

Questions brand owners ask

Which molecular weight should I specify?+
It depends on the dosage form and the mouthfeel you want. Low grades around tens of kDa behave differently from high grades over one million Da in viscosity and capsule behaviour. Send the grade on your spec sheet and we will confirm what it does in your format on a pilot batch before you commit.
Is your hyaluronic acid from rooster combs?+
No. We use sodium hyaluronate produced by microbial fermentation. The source is stated on the CoA, and the documentation trail runs from material lot to finished batch. If your market asks for the origin in writing, that trail is what you provide.
Why does the powder clump?+
Hyaluronic acid is hygroscopic and picks up water from the air. In a powder blend that shows as clumping; in capsules it shows as softening over time. Low-humidity packing and desiccant sachets are the process controls, and the pack format is chosen around that risk.
What is the EU novel food status?+
Oral hyaluronic acid is a food supplement application, and the EU novel food status and permitted dose need checking per market before formula lock. The status is market-dependent and may have changed, so we verify it for the destination market rather than asserting a permanent position.
Can you combine it with collagen or vitamin C?+
Yes. Collagen, vitamin C and elastin are the usual partners. Each addition changes fill weight and flow properties, so the pilot batch re-checks both rather than assuming the base formula carries over. Fill weight is confirmed on the line before production.
What is the MOQ and lead time?+
MOQ is from 500 units for most forms; softgels can start at 1,000 pieces for a pilot, while gummies and stick packs need higher first runs. Lead time is 4–6 weeks for a pilot run after formula and artwork approval, and sampling takes 7–10 days.

Send your hyaluronic acid spec

Send the molecular weight grade, dosage form and destination market. We will check the EU novel food status for that market, confirm the format fit and quote MOQ and lead time. Sampling takes 7–10 days.

Related pages